Roof installation in Dallas

New roofs built as complete systems, from deck to ridge

Roof Installation Dallas TX built for Texas storms

A new roof installation in Dallas is where the whole system gets set right from the start: the deck, the underlayment, the flashing, the ventilation and the field, all installed in the right order to the 2021 codes Dallas adopted. Whether it is a new build, an addition, or a replacement install, the roof is built to take Dallas hail, wind and heat from its first season.

Open 24 hours, every dayItemised written quotePhotos at every stage
Call firstTell us about the build — new home, addition, or replacement — and what the roof looks like on paper
Safety before speedWe check the deck and the structure before any material is ordered
Diagnose the causeWe plan the system around the pitch, the penetrations and the ventilation
Approve the workYou see the written scope before anything is installed

What's included

What a roof installation includes

A new roof is a system, not a surface. The scope covers the deck, the waterproof layers, the flashing, the ventilation and the field — each layer installed in order, each one checked before the next goes on.

01

Deck inspected first

The sheathing is checked for damage, spacing and fastening before any material goes down. A new roof on a bad deck is a new roof that fails early.

02

Underlayment across the field

Synthetic underlayment across the field, with a heavier waterproof layer in valleys, at eaves and around penetrations — the second line of defence under the field.

03

New flashing at every detail

Chimney, wall, valley, skylight and vent flashing are all new metal, installed as the courses go up so each piece laps correctly over the one below it.

04

Ventilation sized to the roof

Ridge vents and clear soffit intake are sized to the roof area, so the attic moves hot air out instead of trapping it against the deck in a Dallas summer.

05

Field installed to pattern

Shingles, metal panels or tile are installed at the manufacturer's pattern, with courses chalk-lined and fasteners placed where the wind rating depends on them being.

06

Permit and final inspection

Dallas requires a permit before any new roof covering is applied, and a final inspection once the work is complete. The permit application lists where debris will go, and the final inspection follows proof of disposal.

Service overview

What roof installation in Dallas actually involves

Roof installation in Dallas is the construction of a complete roof system on a new build, an addition, or a home getting its first roof after a full tear-off. The work follows the same sequence every time: deck, waterproof layers, flashing, field, ventilation — because the order is what makes the system watertight.

Dallas roofs are designed to a 115 mph wind speed under the 2021 codes, and the installation has to deliver that rating: fasteners at the right pattern, flashing lapped the right way, and no shortcuts at valleys, eaves and penetrations. The most common installation failures we are called to fix are all at details — a boot set wrong, a valley cut short, a ridge vent that was never opened — which is why the details get the same attention as the field.

The deck decides the roofA new field on damaged or poorly fastened sheathing will not hold its wind rating. We inspect the deck first and replace what is damaged before the first course goes on.
Details fail firstValleys, chimneys, skylights and vent pipes are where water gets in. Each one gets new flashing installed as the courses rise, lapped so water runs over the joint, never into it.
Ventilation is part of the installA roof installed without balanced intake and exhaust cooks from underneath in a Dallas summer, when roof surfaces reach 150 to 170 degrees. Ventilation is sized and installed with the roof, not added later.
Crew installing architectural shingles on a new Dallas roof
How we workWe verify the cause, compare realistic options, and confirm the work before we leave.

The service timeline

What to expect during your installation

The sequence is the same on every installation, and it is what makes the roof watertight.

01

Deck check

We inspect the sheathing for damage and fastening, and check the structure at valleys and ridges. Anything damaged is replaced before material is ordered.

Stage 1
02

Scope

The written scope names the material, the layers, the flashing details and the ventilation, so the install is agreed before the first bundle arrives.

Stage 2
03

Waterproof layers

Waterproof layer in the valleys and at eaves first, then synthetic underlayment across the field, lapped so water runs over every joint.

Stage 3
04

Field and flashing

Shingles, metal or tile go on at the manufacturer's pattern, with new flashing installed course by course at chimneys, walls, skylights and vents. Ridge vents cap the system.

Stage 4
05

Cleanup and walkthrough

Magnet sweeps across the ground, debris hauled off, and a walk of the finished roof with the crew. You receive the photos and paperwork for the job.

Stage 5

Tools & methods

Tools and methods we use on your installation

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Roofing nail gun

Drives fasteners at the manufacturer's pattern and depth, which is what the wind rating is built on.

02

Chalk line and square

Keeps every course straight and every valley cut true, so the field reads clean from the street.

03

Tin snips and brake

Forms flashing to fit each chimney, wall and valley exactly, instead of forcing a stock piece into place.

04

Fall protection harness and roofing ladder

Keeps every installer tied off on steep pitches, which is how the work is done safely on every job.

05

Moisture meter

Checks the deck for hidden damp before it is covered, so wet sheathing is never sealed under a new roof.

Use cases

When Dallas homeowners call us for installation

These examples show how an installation is planned around the building, not around a template.

New shingle roof installed on a Dallas addition
New roof on a Lakewood additionA second-story addition over a 1920s home, tying a new roof into an old one. The valley where the two roofs meet was rebuilt with new metal, the flashing was woven course by course, and the new field was matched to the old so the addition reads as part of the house.

Full install on a North Dallas new build

A new home with a complex hip roof and three skylights. Deck checked, waterproof layers laid, flashing installed at every penetration as the courses rose, and ridge ventilation sized to the roof. The roof was dried in before the interior work started.

Re-roof install in East Dallas

A replacement install on a home that had carried two layers of shingles. Both layers stripped to the deck, damaged sheathing replaced, and the new system built up from the bottom — underlayment, flashing, field, ventilation — to the adopted code.

Problems we solve

Problems a proper installation prevents

Most installation failures we are called to fix trace to the same few details. Getting them right the first time is the whole job.

ISSUE

Leaks at new skylights and chimneys

Flashing installed course by course as the field rises, lapped so water runs over the joint. A detail finished after the field is a detail that leaks.

SYMPTOM

Shingles lifting in the first wind

Fasteners at the manufacturer's pattern and depth, with seals set properly. The 115 mph design wind speed is only real if the fastening is.

SIGN

Attic heat cooking the new roof

Ridge vents and clear soffit intake sized to the roof, installed with the field so the attic moves hot air out from the first summer.

ALERT

Valleys that pond and leak

Valley metal centred and cut clean, with the waterproof layer beneath it. A valley is a water channel, and it is built like one.

Cost factors

What shapes the cost of a roof installation in Dallas

SIZE, PITCH, MATERIAL AND COMPLEXITY SET THE SCOPE

Phase 01

Roof size and pitch

Square footage drives the material, and steep pitches need more fall protection and more time on the roof.

Phase 02

Material choice

Architectural shingles, standing seam metal, tile and slate each carry different material and labour, and different lives under Dallas hail and heat.

Phase 03

Details and penetrations

Chimneys, skylights, valleys and dormers each add flashing work. A simple gable roof installs faster than a roof cut up with details.

Customer reviews

What Dallas customers say

5.0★★★★★41 Google reviews
★★★★★
“Soon after, the crew got the new roof installed much faster than I expected. As a first-time homeowner, I had never been through a roof replacement before.”
MK
Mandy KramerGoogle review · 4 weeks ago

Questions before we arrive

Roof installation questions Dallas homeowners ask

Roof Installation
Call (469) 960-7533
How much does a new roof installation cost in Dallas?

It depends on the size and pitch of the roof, the material, the number of details like chimneys and skylights, and the condition of the deck. We inspect first and give you an itemised written quote for the installation as scoped — estimates vary, and no two roofs price the same.

Does a new roof installation need a permit in Dallas?

Yes. Dallas requires a permit before any new roof covering is applied, under City Code Chapter 52, section 301.4.6.3. The application lists where debris will go, and a final inspection follows once the work is complete and proof of disposal at a city landfill or transfer station is submitted.

Can a new roof be installed over the old one?

Dallas allows no more than two roof coverings in total, so a roof already carrying two layers must be stripped to the deck. Even where a second layer is allowed, a tear-off lets us inspect the decking and replace what is damaged — which is why we recommend it.

What roofing material is best for a new Dallas roof?

Architectural asphalt shingles are the standard choice for most Dallas homes. Impact-resistant Class 4 shingles are the hail answer for Dallas. Standing seam metal and concrete tile last longer and reflect more heat. We match the material to your roof pitch, the look of the home, and the rules of any conservation district.

Ready when you are

Get your roof installation Dallas TX quote

An inspection, photos, and an itemised written quote for the installation as scoped. Call (469) 960-7533 and tell us about the build.

Roof Installation

Talk with the local team

Request Roof Installation

Call us at (469) 960-7533 or send a message and we will get back to you. We are open 24 hours, every day. Tell us about the new build or addition and we will give you a straight answer on what the roof needs.

3919 Cedar Springs Rd, Dallas, TX 75219Main office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now